Pressing Temperature Too High in a Pellet Mill: Causes, Effects and Control

News 2026-11-21

Pressing temperature too high means the die is running hotter than the material and the die specification can tolerate. The temperature inside the die is generated by friction: the rollers compressing the material, the material passing through the holes, and the material-to-die contact. That heat is carried away by the material flowing through the die. When the heat generated exceeds the heat carried away, the die temperature rises.

The cause is usually one of five things: too little material flowing through the die, so there is less to carry the heat away; too much friction from the roller gap, the die surface or the die specification; material that is too dry; a die with blocked holes, so the remaining holes carry more load; or a material that generates more friction than the die was specified for. Which one it is decides the correction, and the first step is to read the die temperature together with the feed rate and the current.

This article covers how to read the temperature pattern, the process, mechanical and material causes, the effects on pellet quality and on the die, the diagnostic sequence, the safety considerations, and what to confirm when buying a mill.

What “Pressing Temperature Too High” Actually Means

Pressing temperature is the temperature inside the die where the material is compressed and extruded. It is not the same as the motor temperature, the gearbox temperature or the ambient temperature. It is generated by the work done in the die, and it is controlled by the balance between heat generated and heat removed.

Heat generated depends on the roller pressure, the die hole geometry, the material’s friction characteristics and the feed rate. Heat removed depends mainly on the material flow through the die and the moisture it carries.

A die temperature that is too high therefore has two possible directions: too much heat generated, or too little heat removed. The two are corrected differently.

Reading the Temperature Pattern

The temperature and the conditions around it narrow the cause.

PatternLikely causeWhat to check first
High temperature with low current and low outputLow feed rate; the die is starvedFeeder setting, bin flow, feed rate record
High temperature with high currentHigh friction: roller gap too small, die specification too high, dry materialRoller gap, die specification, material moisture
High temperature concentrated in one sectorBlocked holes or uneven feed distribution in that sectorDie hole condition, feed distribution, roller condition
High temperature across the whole die after a die changeDie specification or die seatingCompression ratio, die seating, die bolts
High temperature after a material changeMaterial moisture, density, fibre or friction characteristicsMaterial moisture, die specification against the material
High temperature with smoke or a burnt smellSevere overheating, fire riskStop immediately and follow fire safety procedure

Low Feed Rate and a Starved Die

The most common cause of high pressing temperature is a die running with too little material.

Why a starved die heats up

Material flowing through the die carries heat away. When the feed rate drops, less material passes, so the heat from the rollers and from the friction in the holes is carried away more slowly. The die temperature rises even though the friction per unit of material has not changed.

What causes low feed

  • A feeder setting reduced below what the die requires
  • Bridging in the bin, so the feeder turns but delivers less
  • Material that flows poorly because it is out of specification
  • A worn or partly blocked feeder
  • A feed rate set too low for the die and the material

What to check

  • The feeder setting against the die’s requirement
  • Material flow at the feeder and in the bin
  • The feed rate record against the die temperature record

Restoring the feed rate brings the die temperature down, provided the die has not been damaged.

pellet machine

High Friction from the Roller Gap, Die Surface or Die Specification

A die that generates more friction than normal runs hot even at the correct feed rate.

Roller gap too small

A gap that is too small over-compresses the material, raises friction and temperature, and can char the pellet surface. This is common after a die or roller change if the gap was not reset.

Worn or polished die surface

A die whose hole surface has become polished generates less friction in the hole; a die whose holes are worn or scored generates uneven friction. Either change can produce local hot spots.

Die compression ratio too high

A compression ratio too high for the material raises the pressure and the friction, and the die runs hot at any reasonable feed rate. This is a specification problem and does not respond to feed adjustment.

Worn roller

A worn roller with flat spots does not grip evenly, so some material is over-compressed while the rest slips. The over-compressed material generates local heat.

What to check

  • The roller gap on every station
  • The die hole condition across the die
  • The roller surface
  • The die specification against the material

Material Moisture Too Low

Very dry material generates more friction and carries less heat away, so it heats the die faster.

Why dry material heats the die

Dry material has less water to absorb heat and to carry it away, and its fibres are more brittle. The friction in the die raises the temperature faster, and the die reaches a high temperature at a lower feed rate than it would with correctly moistened material.

What to check

  • The material moisture at the mill inlet against the die’s working range
  • The dryer settings, if a dryer is in use
  • The material source, if a new batch is drier than the previous one

The correct moisture range depends on the material and the die, and it should be confirmed by testing.

Blocked Die Holes

A die with some holes blocked has less open area, so the remaining holes carry more material and run hotter. The high temperature is usually concentrated in the sector where the blockage is, because that sector is working harder.

What to check

  • The die hole condition, hole by hole, in the sector where the temperature is highest
  • The wear pattern across the die
  • The feed distribution, because uneven distribution causes local blockage

Clearing the blocked holes restores the open area and brings the temperature down, but the cause of the blockage should be found first.

What High Pressing Temperature Does to the Die and the Pellet Quality

The heat damages both the product and the die.

  • Pellet quality. Pellets that have been over-heated have a charred or glossy surface, reduced durability, and a burnt smell that persists in storage. They are usually rejected by the market.
  • Die damage. A die that runs hot wears faster, and the hole surface can be affected by the heat. A die that has been overheated may need to be replaced earlier than its expected life.
  • Roller damage. The heat and friction affect the roller surface as well as the die.
  • Fire risk. A die hot enough to char material is also hot enough to ignite dust or fines. Smoke or a strong burnt smell is a fire warning.
  • Energy cost. A die running hot consumes more energy per ton, because more of the input energy goes into heat rather than into forming the pellet.

Diagnosing High Pressing Temperature

Work through these steps.

  1. Read the die temperature together with the feed rate and the current. The combination narrows the cause: low current with high temperature points to low feed; high current with high temperature points to high friction.
  2. Check the feed rate. Is the feeder delivering the rate the die requires? Is there bridging in the bin? Is the feeder worn?
  3. Check the material moisture at the mill inlet, against the die’s working range.
  4. Check the roller gap on every station, and check the die hole condition and the roller surface.
  5. Check the die specification against the material, particularly after a die change.
  6. Check what changed. A die change, a roller change, a material change, a feed setting change or a drying change explains most sudden temperature rises.

If the high temperature is concentrated in one sector, the cause is local to that sector. If it is across the whole die, the cause is global.

Safety Considerations

A die hot enough to char material carries fire and burn risks.

  • Stop the mill if there is smoke or a strong burnt smell. Do not continue running to see whether it clears.
  • Isolate and lock out before opening the die chamber. Confirm zero energy.
  • Allow the die and rollers to cool before touching them. A die that has been running hot can cause burns.
  • Follow the site’s fire safety procedure, including the location of extinguishers and the emergency stop.
  • Do not use water on a hot die. Thermal shock can crack the die.
  • Check the dust collection and the area around the mill for hot particles or smouldering material after a high-temperature event.

Controlling and Preventing High Pressing Temperature

  • Keep the feed rate at the level the die requires, and check the feeder and bin for bridging at each shift.
  • Keep the material moisture within the die’s working range, and check it whenever the material or the drying changes.
  • Check the roller gap on every station at each shift or at the interval the manufacturer specifies.
  • Inspect the die holes at each die change and at defined intervals.
  • Record the die temperature, the feed rate and the current at each shift, so a rising trend is visible before the pellets char.
  • Train operators to treat high die temperature with a burnt smell as a stop-and-check condition, not as a normal variation.

When High Pressing Temperature Signals a Wrong Selection

Repeated high temperature with material that should be within the die’s capability, and with the feed, moisture, die and roller checks clear, points to selection.

Signs that point to selection:

  • The die compression ratio is too high for the material, so the die runs hot at any reasonable feed rate.
  • The die open area is too small for the required throughput.
  • The feeder cannot deliver a stable feed rate at the required level.
  • The material’s moisture range cannot be held within the die’s working range with the drying equipment installed.

In these cases, the die, feeder or drying specification needs review against the material, not repeated adjustment.

What to Confirm When Buying a Mill

Die specification against the material. Confirm the hole diameter, open area and compression ratio suit the material and its moisture range.

Die temperature indication. Confirm the mill has die temperature indication, because it is the primary reading for controlling pressing temperature.

Feeder control. Confirm the feeder can deliver a stable feed rate at the required level and can be adjusted finely.

Drying provisions. Confirm the drying equipment can hold the material moisture within the die’s working range.

Dust and fire protection. Confirm the dust collection and fire prevention provisions suit a biomass line, because a hot die is a fire risk.

Acceptance testing. Confirm the mill is run with your material at the intended feed rate, and that die temperature, current, feed rate and pellet appearance are recorded.

If pressing temperature is running too high and the cause is not clear from the checks above, send the machine model, the die temperature and current, the feed rate, the material moisture, the die and roller condition and what changed before the temperature rose, and the feed, die and drying setup can be reviewed against the material.


AUTHOR / COMPANY INFORMATION

Shandong Changsheng Machinery Co., Ltd. is a manufacturer of biomass pellet production equipment, including ring die pellet mills, complete pellet lines and related process equipment, serving overseas importers, EPC contractors, engineering companies and biomass fuel producers.